Cold-roll steel sheets Wall Mount emergency service Telephone KNZD-05LCD

Location:
shenzhenChina (, Mainland)
Status:
New
Sample Availibility:
yes
Payment Terms:
Cash, Bank Transfer, Letter of Credit, T/T, L/C

Product Description

HOT SALES!!!XeXun TK103-2 Original Vehicle GPS Tracker With SOS Emergency Services and 5 Seconds Intervals Time Audio Monitoring

Product show:

Main Functions :

TK-103-2 Original upgrade version based on TK103 Vehcile tracker
Dimension:80 x 60 x 25mm weight:100g

1) ARM 7 processor inside ,quickly,stable

2) SMS/GPRS location updates

3) 5seconds intervals time tracking
4) Audio monitoring (listen in)
5) SOS emergency services
6)Move and geofence alert
7)overspeed limit alert
8)low battery alert

9)Google map link SMS

10) External Gsm/Gprs antenna

11)Remote oil/electricity cut-off function

12) SD card save data when gprs disconnect

13) GSM ID function

14) Build in motion senser

15) Two Sim Card

1 Summary

Working based on existing GSM/GPRS network and GPS satellites, this product can
locate and monitor any remote targets by SMS or GPRS,and guard against theft of
Vehicle.

2 Applications

Rental vehicle / Fleet management etc

Covert tracking

5 SIM card installation
Make sure that there is no call transfer and call display is on, and PIN code off.
Steps:

Install SIM card A:

1.Open the tracker rear cover, take out the mainboard,and put SIM card A into the
holder.
2. Put in a SD card beside the SIM card A (at the back side of the maniboard).
3. Close the tracker back cover by tightened the screws

6 Startup

Put the SIM card,SD card and battery in place. (NOTE:The tracker turns on atuomatically while the sim card slot B be inserted,and the tracker turns off automatically while the sim card slot B take out.)

After connecting the wires with the tracker and the car,then you can see the LED indicator flashs red arounds the wires connector(re.3.1 wires connector) In 40-60 seconds, the unit will start to work and receive the GSM signals as well as the GPS signals. The indicator keep flashing every 1 second when the unit has received the signals.When this unit receives GPS signals normally, you can use it and do all the following settings.

7 Usage

The tracker has three working modes: Fortifying mode, Tracking mode and Monitoring mode. Modes switch between “fortifying”, “ tracking” and “monitoring”.

When power on the tracker, the default mode is“Fortifying”mode, you can send “ tracker+password” to switch to tracking mode, or send “monitor+password” to switch to

monitoring mode, or “fortify+password” back to fortifying mode.

8 Fortifying Mode
8.1 Engine Started Alert

8.2 Movement Alert

8.3 Power Cutoff Alert

8.4 Application in the Car Alarm System

8.5 Checking the Working Status ( fortify or no fortify )

9 Tracking Mode

9.1 Initialization

9.2 Change the Password
Send SMS password+old password+space+new password to change the password.
(default password: 123456)

9.3 Authorization
There are only 5 numbers able to be authorized numbers.
9.3.1 Setup:Send SMS admin+password+space+cell phone number to set up the first authorized number.The other authorized numbers should be setup by the first authorized number. If the number is successfully authorized, the unit will reply SMS as
“admin ok!”.
9.3.2 Cancel:Send SMS noadmin+password+space+authorized number to delete the authorized number.
9.3.3 For roaming purpose, you have to add your country code ahead of the cell phone number, for example, please send admin123456 008613322221111 to tracker to set 13322221111 as an authorized number.
9.3.4 When an authorized number dials up the unit, it will hang up and report a real-time Geo-info as below:
Lat: 22.566901 long: 114.051258 speed: 0.00 14/08/09 06.54 bat:F Signal:F help me
imei:354776031555474

9.4 Auto-Track
9.5 Geo-fence

9.6 Movement Alert

9.7 Overspeed Alert:

9.8 IMEI Checking:
Send SMS imei+password to the unit to check the IMEI number of the unit.
9.9 SOS Button

9.10 Low Battery Alert

9.11 SMS Center ( or appointed number)

9.12 GSM ID(this function can be add or delect for customization.)

9.13 Motion Sensor(this function can be add or delect for customization.)

9.14 SD Card Function

9.15 SIMcard A-B Transformation

10 Monitoring Mode(voice surveillance mode)
Send SMS monitor+password, the response from the tracker is “monitor ok” then you can hear the voice around the tracker after your call.

11 Remote Oil&Electricity Cut-off Function
This function is using for the car owner to send a SMS remotely to stop a moving vehicle.

11.1 Setup: Send SMS command powercar123456 00 to the tracker to cut off the oil and electricity of the car to stop the car.
Reply format: powercar ok. You will receive such a reply if the setting is successful.

11.2 Cancel: Send SMS command powercar123456 11 to the tracker to restart the car again.
Reply format: powercar ok. You will receive such a reply if the setting is successful

12 GPRS Setting
In order to use GPRS function, the user needs to set IP, Port and APN ( access point name ) by either cell phone, or our PC software.
( NOTE: Some countries or regions should set APN’s User Name and APN’s
Password.)

12.1 Set an IP address and port:
Setup: Send SMS adminip+123456+space+IP address+space+

Cancel: Send SMS noadminip+123456

12.2 Set APN
Setup: Send SMS apn+123456+space+specify apn content.
If setup successful, the tracker will reply SMS “APN ok”.
Cancel: The old APN will be invalid automatically when a new APN is set.

12.3 Set APN’s User Name
Setup: Send SMS apnuser+123456+space+the APN’s user name.
If setup successful, the tracker will reply SMS “apnuser ok”.
Cancel: The old APN user name will be invalid automatically when a new APN user name is set.

12.4 Set APN’s Password
Setup: Send SMS apnpasswd+123456+space+the APN’s password.
If setup successful, the tracker will reply SMS “apnpassword ok”.
Cancel: The old APN password will be invalid automatically when a new APN password is set.

12.5 GPRS transport protocols
As soon as the IP & Port & APN are set up, the user can make a call or send SMS to tracker. The tracker will hand up and report the coordinates to IP address.
The message format sent by tracker to IP address is as following:
Serial number + authorized number + GPRMC + GPS signal indicator + command +IMEI number + CRC16 checksum.

Our Free Platform:

Company Information

Shenzhen Haoday Technology Co., Ltd. is a manufacturer and reseller of GPS tracker and car alarm system with well-equipped testing facilities and strong technical force.

With a wide range, good quality, reasonable prices and stylish designs, our products are extensively used in fleet management, and tracking system and other industries.

Our products are widely recognized and trusted by users and can meet continuously changing economic and social needs.

We welcome new and old customers from all walks of life to contact us for future business relationships and mutual success!



This member's information has NOT been authenticated or verified by importexportleads.net or any third party. Only Gold Members have completed an authentication and verification procedure conducted by third-party credit agencies.

For more information on importexportleads Gold Membership, Click here

Contact Information

Company:
 Shenzhen Haoday Technology Co., Ltd.
Phone Number:
  86-755-88363093
Fax Number: